IMPACT TESTER

Ascott Shop > INSPECTION & TEST EQUIPMENT > IMPACT TESTER
TUBULAR IMPACT TESTER

TUBULAR IMPACT TESTER

Ref: TUBULAR IMPACT

Quantity:   

Choice:
T01-700163 - Heavy Duty Impact Tester 0-100cm scale 1,000.00
T01-700164 - ISO Impact Tester 0-100cm scale 800.00

Impact test describes a method for evaluating the resistance of a dry film of paint,varnish or related product to cracking or peeling from a substrate when it is subjected to a deformation caused by a falling weight.
The coating under test is applied to suitable, thin(normally metal)panels. After the coating has cured, a standard weight is dropped on the each panel from a height that will cause deformation of the coating and the substrate. The test can be carried out with the coated side of the panel facing upwards(i.e.towards the falling weight)or downwards(i.e away from the weight).By gradually increasing the height from which the weight drops, the point at which failure occurs can be determined.Films generally fail by cracking, which is made more visible by the use of a magnifier.

The test can be carried out:
---either as a pass/fail test, the test being carried out from one drop height and with a specified mass, so as to test compliance with a particular specification.
---or as a classification test, to determine, by gradually increasing the drop height and/or the mass, the minimum mass and/or drop height for which the coating cracks or peels from its substrate.

These impact testers consist of a solid base with a guide tube support, some different weights hammers(falling weights)and some different diameters punches. Users can choose different size and weight hammer to simulate paint used different environments. Calibration certificate suppliued as standard

There are two verisons available:

T01-700163Heavy Duty Impact Tester in accordrance with ASTMD2794 , ASTM D 3029 & ISO 6272.2 - 0-100cm scale, 3 falling weights (2 x 1000g & 1 x 300g) and two punch diameters or 12.7mm & 15.9mm

T01-700164ISO Impact Tester in accordance with ASTMD2794 , ASTM D 3029 & ISO 6272.1 0-100cm scale, 4 falling weights (2 x 1000g & 2 x 2lb) and two punch diameters or 20mm & 15.9mm



Click tabs to expand information

Product
Impact Testers
Accessory for
Not applicable
Part Number
T01-700163 -
T01-700164
Range
0-100cm
Accuracy
1 cm graduation scale
Standards
T01-700163 - ASTM D2794, ASTM D3029, ISO 6272.2
T01-700164 - ASTM D2794, ASTM D3209, ISO 6272.1
Features and Benefits
Aluminium oxide guide tube is produced by advanced technology and will never fade or rust.
Both variants are supplied with calibration certificates
T01-700163 - Is the latest design making changing the punch, weight die easiser and faster
T01-700164 - features a ring slot of height limitation making it convienient for the operator to adjust the impact depth
Calibration Certificate
As Standard
Warranty
1 year

Paint testing


     To send a Technical Support Enquiry about this product only CLICK HERE
     We aim to reply to all queries by the end of the next working day.
     The Ascott Shop is a Internet business and we prefer contact by email.
     If you need to contact us by fax, then please refer to the Terms & Conditions page for our contact details.

     For general enquiries please use the Contact Us page.




IMPACT TESTER
Impact TestPanel Impact Test

IMPACT TESTER

Ref: IMPACT TESTER

Quantity:   

Choice:
T01-700161 - 0-50cm scale Tester, 1cm graduation, 1kg hammer 280.00
T01-700162 - 0-100cm scale Tester, 1cm graduation, 1kg hammer 310.00

This Impact Tester is in accordance with the specification in National Standards determination of paint film resistance to impact and the practical requirement of mechanical construction. The operation principle of the impact tester is by means of a weight that drops down from a specified height and impacts a painted panel under test to result in its rapid deformation, and the film resistance to impact is then attained from observing the film to see if it cracks or peels off.
.


Click tabs to expand information

Product
Impact Testers
Accessory for
Not applicable
Part Number
T01-700161 - 50cm scale
T01-700162 - 100cm scale
Range
0-50 cm or 0-100cm
Accuracy
1 cm graduation scale
Resolution
1kg Mass of Hammer
Piercer Specification 8mm dia
Notch of diamter on the bolster block = 15mm dia
Impact depth of piercer = 2mm
Standards
GB/T 1732
Features and Benefits
1kg Mass of Hammer
Piercer Specification 8mm dia
Notch of diamter on the bolster block = 15mm dia
Impact depth of piercer = 2mm
Calibration Certificate
Not Applicable
Warranty
1 year

Paint testing


     To send a Technical Support Enquiry about this product only CLICK HERE
     We aim to reply to all queries by the end of the next working day.
     The Ascott Shop is a Internet business and we prefer contact by email.
     If you need to contact us by fax, then please refer to the Terms & Conditions page for our contact details.

     For general enquiries please use the Contact Us page.




DUPONT IMPACT TESTER
Impact Tester

DUPONT IMPACT TESTER

Ref: T01-700160


Price: 1,500.00

Quantity:   

The DuPont Impact Tester is designed to test the impact endurance of coating material (after coated). Place the specimen with the coated face upwards, and connect it with specified radius Impact Head, then use a certain weight to impact the Impact Head on a fixed height, afterwards, check the damage or deformation of coating .

To perform the impact test for painted and coated materials is to use an impact head with various round angles to touch the specimen in the beginning, and then a selected weight free dropping from a certain height to hit the impacting head on to the specimen below. Run the same way to test three more specimens, leave the samples for an hour, and then evaluate if there is crack on the painting.

It is compatible with ASTM D 2794, JISK 5400, CNS 10756.

Main Technical Parameters

* Instrument scale Length:50-500mm(grade :0mm)
* Mass of hammer:300g, 500g, 1000g
* Piercer specification:1/2, 1/4, 1/8, 1/16, 3/16in
* Notch diameter on the bolster block:1/2, 1/4, 1/8, 1/16, 3/16in



Click tabs to expand information

Product
DuPont Impact Tester
Accessory for
Not Applicable
Part Number
T01-700160
Range
300 - 1000g
Accuracy
1%
Resolution
n/a
Standards
ADTM D2794, JISK 5400, CNS10756
Features and Benefits
* Instrument scale Length:50-500mm(grade :0mm)
* Mass of hammer:300g, 500g, 1000g
* Piercer specification:1/2, 1/4, 1/8, 1/16, 3/16in
* Notch diameter on the bolster block:1/2, 1/4, 1/8, 1/16, 3/16in
Warranty
1 year


     To send a Technical Support Enquiry about this product only CLICK HERE
     We aim to reply to all queries by the end of the next working day.
     The Ascott Shop is a Internet business and we prefer contact by email.
     If you need to contact us by fax, then please refer to the Terms & Conditions page for our contact details.

     For general enquiries please use the Contact Us page.




Got to the Ascott On-line Shop
Got to the Ascott Analytical Equipment website